Maytag Bravos Xl Washer Continuously Runs
Maytag is one of the most affordable and reliable washer brands in the market today. Having been in the market for more than a century, you would expect them to have already figured out all their kinks. However, why does a Maytag washer keep spinning/not spinning/rinsing?
Maytag washer keeps spinning for various reasons like a faulty driver belt, defective motor control board, and a worn-out clutch band kit. Your washer might be stuck in the spin or rinse cycle when you use excess power detergent, timer issues, drain control issues, and electrical problems.
This article will look at some of the problems your Maytag washer may face, like when it keeps spinning, won't go into spin cycles, won't stop spinning, won't spin fast, won't complete a spin, and how you can mitigate them. It will also offer you a few tips on the best ways to inspect your washer without causing further damage, even if you are not tech-oriented.
Maytag Washer Not Spinning: Causes / How to Fix It
Cleaning laundry with a washer should be an easy and enjoyable process. You need to insert your clothes in the machine, press a set of buttons, and comfortably wait to take them out when clean. But, what do you do when you find your load sopping wet?
Well, it tells you one thing; your washing machine is having trouble spinning. But how do you solve such a problem?
Inspect the Lid Switch
The Maytag washer lid has a small protrusion on the underside that activates the lid switch when you close your top-loading washer. It helps to signal that the washer is sealed correctly. If the lid is open, the lid switch stops your washing machine from spinning as a safety precaution.
When it becomes defective, it still prevents the washer from turning. It does not matter if the lid is closed.
Therefore, you should ensure that the lid switch triggers every time you open and close the lid. If the protrusion that activates the switch is bent out of shape, try to re-establish its position. However, if it does not help, consider obtaining a replacement.
The following is a video on how to inspect the lid switch when your Maytag washer is not spinning:
Inspect the Drive Belt
When the drive belt is broken or loose from the pulley, your Maytag top load washer will not spin. The washer may agitate during the wash cycle and make some noise due to the running motor causing you to think that it is working. However, the drum remains still.
To check that the drive belt is the problem, you need to access the washer's back panel. Inspect and see if the drive belt is on the pulley system. If loose, you can try to tighten it. However, if the belt is broken or damaged, you need to purchase a replacement that is made explicitly for a Maytag washer.
Check Whether the Load Is Well Balanced
If the load you put in the washer is unbalanced, your machine may also fail to spin. This mainly happens when you insert too many clothes or bulky items in the drum. Your load may settle on one side of the drum disrupting the spinning motion.
If you suspect that the reason your washer is not spinning is a weight distribution problem, you can try to rearrange your clothes in the drum and restart the cycle again. Additionally, inspect for any clothes that may have jammed in the drum and remove them.
Avoid Overstuffing Your Machine
Even though you do not like washing clothes, you do not need to stuff all your clothes in the washer to clean all of them in one go. Overstuffing your machine may prevent it from spinning. When you overload the washing machine, you are placing the transmission and motor at risk.
However, the motor coupling fails to protect these two parts. The motor coupling connects the machine transmission to the motor. You should inspect the motor coupling and ensure that it is in a good state. If broken, purchase a replacement that matches your washer model.
Maytag Washer Won't Go into Spin Cycle: Causes / How to Fix It
If your washer's spin cycles do not start, then your machine may have a loose or broken belt. You need to access the back panel of the washer to tighten or replace the belt. The spin cycles may also not start if the lid switch is broken. If it does not click every time you close the lid, then replace it. Remember to test the new switch after installing it.
If none of these methods work, then the problem may be with the agitator solenoid or the controls. You should, therefore, seek help from a professional appliance repair person.
Maytag Washer Keeps Spinning: Causes/ How to Fix It
A common problem that you may encounter, especially with front-load Maytag washers, is when it keeps spinning without advancing to the next wash cycle. But how do you troubleshoot such a problem?
Ensure That the Load Is Balanced
Your washer can support a certain number of items at a go. Maytag washers are mostly built to accommodate a moderate to a high number of items. While it is not advisable to overload your washer, you should also not underload it. If your drum only has a few items, your washer may fail to balance the load once it enters the spin cycle. As a result, your washer may remain in the spin cycle for a long time.
Use the Right Detergent
You should only use the recommended amount of detergent when washing clothes with your Maytag washer. When you use too much detergent, the soap suds can accumulate in the drum and washer's sump. It forces the sensors of the machine to continue its spin cycle until all suds are removed.
You can solve the problem by running several full wash cycles without any detergent or clothes. It helps to get rid of any residual detergent that may still be in the system.
If none of these troubleshooting options work, get a repair technician's help since the problem may be a bit more technical.
Maytag Washer Won't Rinse and Spin: Causes/ How to Fix It
If your Maytag washer works well but does not spin or rinse, then it most likely has a problem with its drive belt. It may have slipped off or broken. As such, the motor that is responsible for rinsing and spinning may not function appropriately.
You can inspect the belt by opening the back panel of the machine. However, you have to be careful not to cause any further damage, especially when handling the motor.
Copyright protected content owner: Readytodiy.com and was 1st posted on 2020-11-21. .
Maytag Washer Won't Spin Fast: Causes/How to Fix It
Several reasons may cause your Maytag washer to spin slowly. Some are critical cases that may require a technician's help, such as a broken belt or an issue with the motor. Others are not so serious, and you may troubleshoot and handle them on your own.
Do Not Overload the Machine
Overloading a washing machine may cause an imbalance in the drum. The machine may, therefore, not run properly. Its spins can be too slow and may even stop mid-cycle. Therefore, it would be best if you tried removing some of the clothes from the washer and restart it.
Inspect the Drainage
Is the machine draining correctly? Poor drainage negatively affects how a washer works. Ensure that water drains out freely without any blockages if you want your machine to spin fast. Always ensure that the drainage pipes are free from clogs and kinks.
Inspect the Water Level Switch and Hose
If the water level hose is clogged, your washer may not spin fast. To perform an inspection, you need to access the front panel and locate the tube that connects the tub with the water level switch. Check for any debris and lint in the hose pipe. You can clean by either blowing the hose or tapping it on the side.
Additionally, inspect the water level switch using a voltmeter to find out it receives enough power.
Copyright article owner is Readytodiy.com for this article. This post was first published on 2020-11-21..
If there are no changes to your washer spins' speed after following the above steps, get help from a professional washing machine maintenance specialist.
Maytag Washer Won't Complete Spin Cycle: Causes/How to Fix It
When your washer stops working mid-cycle, it may likely have a timer problem. It may be hard to diagnose the problem with an old model washer. However, modern washers display an error message and abort the cycle.
Another common issue is when the heater is working poorly. You can test this by setting your heater on a cycle and watching how long it takes for the cycle to stop.
When the machine overheats, it can cancel itself mid-cycle and even fail to start-up. The main issue may be a faulty thermistor. If you notice your washer is becoming too hot, try and give the machine enough time to cool between washes.
If it stops again mid-cycle, then you may need to replace the thermistor. Also, remember to check the functionality of the timer. If it is not functional, you can easily replace it too.
Final Thoughts
If you are still stumped and do not know which problem to address, you should seek professional help from maintenance specialists. They can further look into other more technical issues like if the motor control board is dis-functional, a defective rotor assembly, or even worn-out spine tube tabs and drive blocks.
Related Articles
Maytag Washer Keeps Draining
Maytag Washer Won't Turn On
Maytag Washer Making Loud Noise During Wash Cycle
My Maytag Washer Won't Work: How to Fix
ReadyToDiy is the owner of this article. This post was published on 2020-11-21..
Maytag Washer Sensing Light Blinking
Source: https://readytodiy.com/maytag-washer-keeps-not-spinning-rinsing-0051/
0 Response to "Maytag Bravos Xl Washer Continuously Runs"
إرسال تعليق